DIY: Rebuilding a screen porch

The porch before demolition

This summer I have a full-time, non-paid job as a carpenter’s apprentice.  We are rebuilding our screen porch, and Mike is the carpenter.  He named me “The Apprentice”, not to be confused with the Donald Trump variety. 

What Mike sees as the apprentice may vary slightly from my view of the roles and responsibilities of an apprentice.  He thinks I should shadow him so I can learn the trade.  But not being one to sit still very long, I am often back in the house doing chores with the comment “call me if you need me”.  Ok, you can already see a few dilemmas.  Mike is holding a board, and he needs a nail.  And he yells “Diane!  Diane!  Come out here!” 

So over the past 6 weeks, I’ve settled into my own apprentice groove.  Basically I am the gopher for screws, tools, staples, wood, and power drills.  I hold boards while Mike fastens them into place.  I hold boards he is “ripping” on the table saw and “cross-cutting” on the radial arm saw.  I accompany him on many trips to Lowe’s, and I help select new boards.  I offer opinions on various approaches to the building, and am sometimes Mike’s “voice of reason” (his words, not mine). 

So, keep in mind that this DIY post on re-building a porch is coming from the vantage point of the apprentice, meaning it will be in very elementary form.  Why?  That’s all I know.

The “old” screen porch

Our house was built in 1989, and there is a screen porch off the kitchen.  The bottom of the porch is brick, and the top is an American Cedar wood frame to which screens are attached.   And therein lies the problem.  American Cedar s not impervious to weather, and the wood was painted and trapped rain and moisture over the years.  The result was rotting wood, and until we were able to rebuild the porch this summer, the porch roof has been supported by two large jacks.

Mike at Pro-Build Lumber

Not wanting to make the same mistake, we decided to rebuild the porch with western red cedar which holds up well in wet conditions.  After checking a couple of local lumber yards, we decided to purchase 4x4 architectural (smoother finish than rough cut) western red cedar posts from Pro-Build (formerly Carter-Lee), a well-known lumber yard in Indy.

Rebuilding the screen porch

1.  Replace the 2 corner posts.

The corner posts are the primary structural support for the porch, and so we tackled these first.  One of our first discoveries was that these posts actually went the ground to the ceiling, and we could not see the post below the brick as it was encased in a square brick casing.  And without Superman eyes to see through the brick, you had to look into the top of this brick casing with a flash light. 

With the floor jacks in place, Mike cut out the first post.  He found rotted wood below the brick line and used a shop vacuum to get out the pieces of wood.  He then realized that the base was not level for one of the beams.  He created a new bottom using concrete and a metal screen.  He also drilled  a “weep hole” in the brick so water would have a place to drain.

Mike cutting out the old post 

Rotting wood

Looking into brick enclosure where post used to be

The roof was being held in place by the jacks, and the next challenge was to get the side beams in place between the ceiling and the brick encasement.  Bottom line is the beams would not fit into this tight angle, so Mike had to  “dado” cut the corner post into two pieces.  He then put the beams in place in the corners and joined them with wood glue and weather-resistant deck screws.  Ok, I had no idea what "dado" meant, and I found the following in the dictionary:  a rectangular groove cut to make a joint in woodworking.

Dado cut on radial arm saw

Installing bottom section of corner post

Gluing dado cut board

He “toenailed” 4.5 inch deck screws through the new beam and 2x4s and 2x12s beams that held the roof in place.  Again, dictionary at the ready; "toenail" is  driving a nail at an angle through a board. 

And every time he installed a new post, he used the jacks to raise the roof slightly so the new posts would slip into place. He would then lower the jack so the post would be load-bearing.

2     2. Replace the other 8 posts. 

      On the old porch the posts sat on top of a horizontal piece of wood which sat on the brick.   It looked good, but the horizontal wood collected water and moisture.  Our friend Craig recommended placing the posts directly on the brick and eliminate the need for the horizontal boards. Another new approach was using right angle galvanized steel brackets to support the top of these beams into the roof beams.

Mike replacing post

Front posts in place

When Mike removed the beams next to the brick wall of the house, I got the job of scraping caulking off the bricks.  I used the Fein Multi-Master with a putty remover tool for this job. Mike then put new clear caulk in place before installing the new beams.  This eliminated any gaps between the bricks and wood thus avoiding insects entering the porch.

Removing old caulking from bricks

Installing new caulking

3     

       3. Install upper level horizontal wood between the posts.

When Mike removed several of the old posts, he found that the wood between each end was in good shape. Keeping them for reuse, he salvaged the beams in such a way that two sides retained the original rough-cut finish and paint.  These were then used as non-structural trim between each of the posts at the top that matched the ceiling and remaining trim on the porch.

Horizontal trim piece

4.   Install 2 door posts.

We decided to leave more of the brick exposed on the door posts, and Mike cut the new posts to sit on the brick and to then extend to the floor.  This was an extremely challenging task.  I'm happy to say that I was somewhat removed from this chore as our friend Kevin became the apprentice that day.  After measuring, cutting, cutting a second time and a good amount of cursing, the posts were put in place.

Door beam in place

5     5.   Install a new wooden screen door. 

First, let me say that I hated the original door since I moved into the house.  It was flimsy and had been shored up over the years with additional wooden brackets, a steel rod and a hook and eye closure.  So I was pretty excited to pick out a new unfinished wooden screen door at Lowe's.   We found a simple door and a wooden insert for the bottom of the door.  The wooden insert would prevent cats trying to escape or other animals trying to enter.  I know, I might be a bit paranoid (or overly dramatic) here...

Screen door insert

My job was to finish the wood door with stain and a waterproof finish.  First I sanded all the wood to remove splinters.  And as you might expect, within the first 5 minutes a 3 inch splinter was sticking straight out of my finger.  I pulled it out and discovered that if you are going to bleed on the wood, this is a good time to do it because you can sand it right off. 

We then selected an Olympic outdoor wood stain that included the waterproof finish. We tried to match the red cedar, and let’s just say that we are getting used to the orange-ish color of the stain which has a certain rustic look. I applied two coats over a several day period. 

Staining the insert

Mike carefully measured and installed the door with three hinges.  Next he installed a "transom" piece(goes immediately above the door) and the wood trim inside the door.  He then installed the new door handle.  Voila!  We have a wonderful new door to replace the ugly old door. 

Putting hinges in place

Carefully adding the transom

 

New screen door!

So, six weeks have elapsed, and the porch is structurally stable and looking good!  And yesterday we made another trip to the lumberyard to purchase more red cedar for the trim.  Yes, there is more work ahead…

But last night as we sat in the screen porch and watched a wild thunderstorm and drank martinis, I felt pretty good about our progress and my new “apprentice job”. 

Stay tuned for Chapter 2 of Rebuilding a screen porch, where we finish the trim work!

Diane

House Makeover: Re-purposing Rooms

If you are like me, you have at least one room in your house that you don't use much.  Possibly it became a storage room or junk room over the years. That's when  I take a hard look at the room.  And the wheels start turning...Could I use the room differently?  Could I re-purpose the room to meet my family's hobbies, interests or lifestyle?

Very comfortable study

When I first moved into this house,  formerly "Mike's house", and now "our home",  I wanted a room of my own for reading, writing and hobbies.

One of our upstairs bedrooms was a storage room for Mike's memorabilia from his family, college days and career.  We agreed this was the best room for my study, and so I got to work packing up the memorabilia in plastic bins to be stored in the basement.

Pottery Barn table as a desk

Wanting a bright, cheery room, I selected a Sherwin Williams Tangerine(SW6640) for three walls and Outgoing Orange(SW6641) for the accent wall.  After I finished painting, we moved in two chairs and a desk from my house.  I added sheer curtains and some favorite art, and voila, I had a newly re-purposed room.

Today I use this room for writing, reading, napping and watching television with my sweetie on cold winter nights.  Mike and I both love hanging out in my study.  It's a cozy oasis!

Studio

And as I got settled into our home and retired life, I found time for long-neglected hobbies.  I wanted a space where I could spread out my beads or sewing project.  And if I didn't finish the project for several days, and provided the cats didn't disturb it, it would be waiting for me exactly as I left it.

There was a Jack 'n Jill bathroom adjoining my study and another bedroom.  It was a huge room with two sinks and mirrors and a separate room with toilet and shower.  Basically it was intended to be a shared bath between two bedrooms.

I imagined the early morning light through the huge arch window illuminating my studio, and Mike and I agreed this was the perfect place for hobbies!

I painted the room Sherwin Williams Compatible Cream(6387) which has a soft yellow hue(unfortunately the picture doesn't accurately reflect that). We added honeycomb blinds and drawer storage units from The Container Store.  This is where I store beads, sewing and painting supplies. And the final touch was re purposing my parent's 1960 vintage kitchen table to serve as my work surface.

So now I have a wonderful little alcove for my jewelry, sewing and painting hobbies.  And yes, I've already heard all the jokes about the convenience of having a toilet nearby...

Formal dining room with brass chandelier

And then there was the formal dining room.  It housed Mike's grandmother's beautiful antique dining room set.  A wonderful drop leaf table, 8 chairs, buffet and mirror graced this room.

But our dining and entertaining style is more casual, and we always use the antique oak dining table in the kitchen.  In the past several years, we've only used the formal dining room two or three times.  And as you can tell from this picture, it had become  a storage room for guitars, glassware and even a bread machine.  



One day our friend Melanie saw the guitars in the room and suggested that we re-purpose the room into a music room.  Melanie is an interior designer, and she has a great eye for functionality and design.  She recommended we set up a coffee table and comfy chairs for playing guitar.  She thought that hanging guitars on the wall would serve as artwork.  Mike and I loved the idea!

So this Spring I packed up the glassware and items that were being stored in the buffet.  We then moved the antique dining room set into storage, to be sold later.

New modern light fixture in the music room

First on the list was replacing the horrible brass light fixture.  We found a beautiful modern light fixture on sale at Lowe's, and Mike promptly hung it.  We then donated the brass light fixture to Habitat for Humanity's Re-Store.

We retrieved my square metal and glass coffee table from our storage unit, and it became the centerpiece of the room.

Fabric for our new chairs

We started shopping for chairs for this room.  Our criteria was a comfy chair with low arms so we could easily play guitar.  We wanted small chairs that would not overpower the room, and of course we wanted a reasonable price.

After a lot of shopping, we found the perfect chair.  And we were happy to discover that the chairs were made locally by Best Furniture Company in Indiana.  We picked a fun fabric and placed the order for the chairs.

Sample paint colors with new chair

The chairs arrived about four weeks later, and we set them up in the dining room and began to search for paint colors.  Melanie suggested a darker color on the bottom and lighter color on the top to take advantage of the existing chair rail.

We bought sample paint at the Sherwin Williams store, and tried it out on the walls.  We decided on Sierra Redwood(SW7598)  for the bottom and Interactive Cream(SW6113) for the top.

New music room

And we ABSOLUTELY LOVE how this room turned out.  The only thing left to finish is hanging the guitars on the wall once we purchase hangers.

Mike and I find it so convenient now to pick up a guitar, sit down in a chair and play a few tunes.  If only this new music room would automatically improve my guitar skills...







So, if a room isn't working out for you, or you are tired of all that junk, don't be afraid to change it.    We are quite happy to be making this house our own, with rooms that reflect our personality and hobbies!

Hmm...I wonder what room is next???

Diane